Main Page

From CALAO Systems MediaWiki
Revision as of 10:10, 6 June 2013 by Ghermant (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Wiki for Calao-Systems ARM Linux Embedded boards


Introduction
The main goal of this wiki is to show how to build and flash the required binaries for the Calao-Systems Embedded boards.
Our embedded boards registration in Buildroot is actually in progress. See here for more information about buildroot).

Note: Barebox is now the default bootloader for the calao embedded boards. (See herefor more information about barebox)

NOTE: When a new board is launched, calao-systems tries to submit the required patches to the barebox, linux kernel & 
buildroot mainline

Click here to see the status of the calao board support in barebox, linux kernel and buildroot mainline

Contents

Computers On Modules

QIL-A9260

Board Dimension 36 x 85 mm
Soc ATMEL AT91SAM9260 @ 180MHz
NAND 256MB NAND Flash (8bit),
SDRAM 64MB SDRAM (32bit @ 90MHz)
DATAFLASH 2Mbit (SPI)
SPI EEPROM 64Kbit (SPI)
RTC 1x RV3029C2 (I2C)
SD Card 1x Micro-SD
Expansion 1x 128 pin connector (EBI, USB Host, USB Device, Ethernet 10/100, DBGU, JTAG, I2C, SPI, SSC, USART, Timers...)

QIL-A9260 Software

QIL-A9260 Hardware Reference Manual


QIL-A9G20

Board Dimension 36 x 85 mm
Soc ATMEL AT91SAM9G20 @ 400MHz
NAND 256MB NAND Flash (8bit),
SDRAM 64MB SDRAM (32bit @ 133MHz)
DATAFLASH 32Mbit (SPI)
SPI EEPROM 64Kbit (SPI)
RTC 1x RV3029C2 (I2C)
SD Card 1x Micro-SD
Expansion 1x 128 pin connector (EBI, USB Host, USB Device, Ethernet 10/100, DBGU, JTAG, I2C, SPI, SSC, USART, Timers...)

QIL-A9G20 Software

QIL-A9G20 Hardware Reference Manual


TNY-A9G20-LPW

Board Dimension 36 x 41 mm
Soc ATMEL AT91SAM9G20 @ 400MHz
NAND 256MB NAND Flash (1.8V/8bit),
SDRAM 64MB SDRAM (1.8V/32bit @ 100MHz)
RTC 1x RV3029C2 (I2C)
SD Card 1x Micro-SD
USB Device 1x Port USB (microUSB connector)
Expansion (Top) 1x 50 pin connector / Top Side (I2C, SPI, USART, SSC, MCI, ISI, TC)
Expansion (Bottom) 1x 60 pin connector / Bottom Side (USB host, Ethernet RMII, I2C, SPI, USART)

TNY-A9G20-LPW Software

Hardware Reference Manual

Single Board Computers

USB-A9263

Board Dimension 36 x 85 mm
Soc ATMEL AT91SAM9263 @ 180MHz
NAND 256MB NAND Flash (8bit),
SDRAM 64MB SDRAM (32bit @ 90MHz)
SPI EEPROM 64Kbit (SPI)
Ethernet 1x 10/100
USB Host 2x Port
USB Device 1x Port USB
SD Card 1x Micro-SD
Expansion 1x 50 pin connector (I2C, Audio, Video )

USB-A9263 Software

USB-A9263 Hardware Reference Manual


USB-A9G20-LPW

Booard Dimension 36 x 85 mm
Soc ATMEL AT91SAM9G20 @ 400MHz
NAND 256MB NAND Flash (1.8V/8bit),
SDRAM 64MB SDRAM (1.8V/32bit @ 133MHz)
Ethernet 1x 10/100
USB Host 2x Port
USB Device 1x Port USB (front shared with DBGU/JTAG or back)
Debug 1x JTAG & 1x DBGU over USB (FTDI FT2232D) or 1x JTAG & 1x DBGU on board
RTC 1 RV2039C2 (I2C)
SD Card 1x Micro-SD (SPI under ethernet port) or 1 via Expansion port
Expansion 1x 50 pin connector (I2C, SPI, USART, SSC, MCI, ISI, TC)

USB-A9G20-LPW Software

USB-A9G20-LPW Hardware Reference Manual


SKY-S9500 aka Snowball

Board Dimension 85 x 85 mm
Soc STE A9500 @ 1GHz
SDRAM 1GB LPDDR2
eMMC 4GB(SDK)/8GB(PDK)
Memory slot 1x microSD
Video 1x HDMI connector + 1x CVBS Cinch connector
Ethernet 1x 10/100M
Connectivity Wifi, Bluetooth, GPS Combo module
Sensors 1x 3D Accelerometer/Magnetometer + 1x 3D Gyrometer + 1x Pressure sensor
USB OTG 1x Port
Audio 1x Audio out + 1x Audio in
Debug 1x JTAG & 1x DBGU over USB (FTDI FT232R) on board
Misc 1x reset + 1x user push button + 1 user led
Expansion 1x 16 pin header (I2C, UART, GPIO ...)
Expansion (*) 1x 60 pin connector (I2C, SPI, SD, UART, FSMC, HSI ...)
Expansion (*) 1x 120 pin connector (LCD, DSI, CSI, FSMC, Audio, ...)
 (*) Only available on the PDK version 

SKY-S9500 Software

SKY-S9500 Hardware Reference Manual

HABA (Home and Building Automation) Controllers

HABA-KNX-EXPLORER

Casing RAIL DIN 9 Modules,
Power supply 9-36VDC 5VDC-2A,
Soc ATMEL AT91SAM9G20 @ 400MHz
NAND 256MB NAND Flash (8bit)
SDRAM 128MB SDRAM (32bit @ 133MHz)
RTC 1x RV3029C2 (I2C)
USB Host 2x Port
USB Device 1x Port
Ethernet 2x 10/100
RS232 1x Port (Isolated)
RS485 2x Port (Isolated)
I2C 1x Port
Dry contacts 4x (Isolated)
KNX/TP1 1x Port isolated
SD Card 1x Micro-SD
Expansion 1x 50 pin internal expansion connector (compatible with DAB-MBUS, DAB-ZigBee, DAB-KNX/RF, 6LowPan...) with front panel antenna.

HABA-KNX-EXPLORER Software

HABA-KNX-EXPLORER Quick Reference Guide

HABA-KNX-EXPLORER Getting Started Guide


HABA-KNX-LITE

Casing RAIL DIN 6 Modules,
Power supply 9-36VDC 5VDC-2A,
Soc ATMEL AT91SAM9G20 @ 400MHz
NAND 256MB NAND Flash (8bit)
SDRAM 128MB SDRAM (32bit @ 133MHz)
FLASH 2Mbit (SPI)
RTC 1x RV3029C2 (I2C)
USB Host 2x Port
USB Device 1x Port
Ethernet 1x 10/100
KNX/TP1 1x Port isolated
SD Card 1x Micro-SD
Expansion 1x 50 pin internal expansion connector (compatible with DAB-MBUS, DAB-ZigBee, DAB-KNX/RF, 6LowPan...) with front panel antenna.


HABA-KNX-LITE Software

HABA-KNX-LITE Quick Reference Guide

Atmel SAM-BA for Calao boards

HMI Development platforms

Expansion Boards

USB Keys

Personal tools
Namespaces

Variants
Actions
Navigation
Toolbox